
greater Phoenix metro
Get your garage door opener repaired today
Most openers that stop working need a circuit board or a sensor, not a replacement. We test the unit and photograph what we find before recommending anything, and decide together if repair is the best option for you and your opener.
What Happened?
Please click for further details.
As fast as same day for qualifying jobs, Monday to Saturday.
- 5.0 on Google, across 5,400+ reviews
- 4.8 on Yelp
- Licensed, bonded and insured · AZ ROC 308754 and AZ ROC 349928
- 30,000+ jobs since 2016
What it can cost
From $160
Opener repair
Most common repairs are safety sensors, gear and sprocket, or the logic board. Labor is additional.
$69
Service call
Charged when a technician is dispatched to diagnose. Waived when you go ahead with a repair (parts and labor). No charge on a warranty visit.
Which part failed decides the final price: a gear and sprocket costs less than a logic board. You get the figure at your house, before anything is started.
Repair it or replace it
| Criterion | Repair | Replace |
|---|---|---|
| Unit age | Under about twelve years, and the rest of the unit is sound. | Older than fifteen, where the next part is close behind this one. |
| Is the part still made | Gears, capacitors and boards for current and recent models are stocked. | Discontinued boards on a unit nobody supplies parts for any more. |
| Drive or board | The gear and sprocket, or the trolley. Mechanical, bounded, and cheap. | A failed logic board on an older unit, where the board approaches the price of a new opener. |
| Safety standard | Safety sensors installed and working, which is everything made since 1993. | No safety sensors at all. That unit is not compliant and should not be kept in service. |
| Relative cost | Under about a third of a new opener installed. | Once the repair passes half, the new unit is the better buy. |
The technician gives this recommendation at your house, and recommends the repair whenever the repair is the better value. An opener that may only need a gear is not an opener that needs replacing.
How the repair works

Step 1
Call or book
Tell us what it is doing and what it sounds like. Phone calls answered 24/7. If we miss you during service hours, we call back in under 10 minutes.

Step 2
Diagnosed on the unit
Power, board, drive and safety circuit are checked in order, so the fault is found rather than guessed at.

Step 3
Repaired and re-set
Part replaced, travel and force limits re-set, and the safety reverse tested before we leave.
Why openers fail
These are the three most common opener repairs we see in Arizona each week.
Stripped gear and sprocket
The plastic gear that drives the chain or screw is the designed wear point, and it is rated in cycles rather than years. When it goes, the motor still runs and nothing moves, which is why the symptom sounds catastrophic and the fix usually is not. On a unit under about twelve years old this is a straightforward repair with the part on the truck.
Logic board failure
The board sits in the hottest part of the house. A garage ceiling in July runs well above the temperature the electronics were rated for, and capacitors and solder joints age accordingly. The receiver that listens for your remote is part of the logic board, so a remote that has lost range is a board symptom too. This is the one genuinely local cause on this page, and it is the reason an opener here does not last as long as the same unit in a milder climate.
Excessive noise from worn out parts
Grinding, rattling or a loud bang on every cycle usually means a worn gear and sprocket, a dry or loose chain, or a worn trolley. The opener still works, so it is easy to put off, but a part that is already noisy tends to fail without warning. Catching it early is normally a smaller repair.
What not to do
Do not keep cycling an opener that hums
A unit that hums and stops could be stalled against something, and every retry sends current through a motor that is not turning. A stalled motor cooks itself in minutes, which turns a worn gear and sprocket into a whole new opener.
Do not buy a remote before testing the receiver
The wall button working and the remote not working points at the receiver or the pairing, not the handset. Test it first. We frequently see homeowners spend money on this unnecessarily, when it could be something we can test during a scheduled service visit.
Brands we service
Authorized LiftMaster Dealer, and we work on the rest of the market too.
- LiftMaster
- Chamberlain
- Genie
- Craftsman
- Linear
- Wayne Dalton
- Overhead Door
- Marantec
Remotes and keypads
Remote and keypad faults are usually the receiver or the pairing, not the handset. A new remote or keypad is from $67 before labor or service call.
The wall button works and the remote does not
Then the drive and the board are fine. That leaves the remote battery, the pairing or the receiver in the motor unit, which is one of the cheaper visits we make.
Nothing works, or only from a few feet away
If neither the remote nor the wall button works, the logic board or the receiver is the likely cause. A remote that only works up close after a fresh battery means the receiver is losing sensitivity. That is a repair at the unit, quoted at your house before any work starts.
Pairing lost after a power cut
It is rare, but on a LiftMaster, remotes and keypads can drop their pairing when the unit loses power. A re-learn takes minutes. The LiftMaster repair page covers it in more detail.
Before you buy a new remote
Note the color of the learn button on the motor unit. On most brands that color is what tells a supplier which generation you have, and a remote made for a different generation may not pair. A keypad you have lost the code to is a reset you can do yourself in about 10 minutes. With a new opener, new handsets and a keypad come with the unit and get programmed before we leave.
“Super nice and well versed in his craft! Not at all pushy, and actually helped me reprogram the key pad I thought needed to be replaced. He did an amazing job repairing the wiring I damaged this morning.”
“Jordan did an excellent job with our garage door opener. He explained the steps he was going to use to make our garage door work. He would finish one area of the repair and then he would let me know of other issues that our door was having and explain the cost to me. At first I thought he was just adding more money to the job like some other places do but he was just keeping me informed. I would recommend him to any of my friends and family. You have a great employee there.”
Rodrigo Dominguez · June 2025
“My garage door jammed partway open at 9am and I assumed I was doomed to spend a fortune fixing it after dealing with the hassle of getting someone out to look at it. Instead Jeff B. showed up by noon, was friendly, professional, and diagnosed and fixed the problem. I wasn't pressured to buy new equipment despite the age of my door and opener. It's running great and I couldn't be happier.”
Michael Christiansen · February 2025
“We are really impressed with Same Day Garage Door Services. This week, Mike W. came out to repair our garage door opener. He was very knowledgeable, friendly and really knew his stuff. He arrived at our home within a few hours, on the same day we called. Professional, competent service at a fair price. We would not hesitate to recommend Mike W. to our family and friends.”
Dave Daly · March 2025
Questions
Most can be repaired. Age, whether the part is still made, and whether it is the drive or the board decide it, and the comparison above is the same one the technician uses at your house.
Authorized LiftMaster Dealer, and we repair and install Chamberlain, Genie, Craftsman, Linear, Marantec and Overhead Door, for homes and businesses. We also repair Wayne Dalton openers.
Under 2 hours on site for common repairs. The common gears, capacitors and receivers ride on the truck, so it is normally finished on the first visit.
Not usually. A new opener goes onto a sound door and existing track. If the springs or rollers are at the end of their life the technician will say so and quote it separately, and you can decline it.
Often the same day for qualifying jobs, Monday to Saturday, depending on where you are and what is already booked.
Related pages
- LiftMaster repairModel-specific diagnosis, error-code patterns and genuine parts.Brand page
- Opener installationBelt, chain and wall-mount, supplied and installed. Wall-mount opener labor is $299.From $975.20 installed
- Sensor repairIf it reverses on the way down, start here. Often a two-minute fix you can do yourself.Try this first
Opener not working?
Call and describe what it does when you press the button. That usually tells us whether it is the gear, the board or the remote.
Phone calls answered 24/7. Booking available 24/7.


