Decision guide
DIY garage door repair versus hiring a pro
Most jobs on a garage door are safe to do yourself, and we list them. A few involve stored spring energy and should never be attempted at home. This page sets out the cost, the time and the risk.
Written by Same Day Garage Door Services. Our prices come from our published price list. Every outside fact was read on its source between 17 September and 8 October 2026, and each one links to where we got it.
Warning
Safety warning. Garage door springs, cables and bottom brackets are under extreme tension and can cause serious injury or death if they slip or break. This guide is general information only. If your repair involves springs, cables, or brackets, stop and call a licensed professional.
Do not adjust, wind, unwind or replace springs yourself. A torsion spring stores enough energy to break bones. Spring work needs proper winding bars and training. Call a licensed technician: (480) 750-7975.
Never loosen a cable or bottom bracket while the springs are under tension. These parts hold the spring's load. Leave them to a professional.
Unplug the opener (or switch off its circuit breaker) before working on it, and make sure no one can plug it back in or press a remote while you work. Remove batteries from remotes or keep them with you. Hardwired openers: turn off the breaker and tag it.
Pull the emergency release only with the door fully closed when possible. If a spring or cable is broken, an open door can slam down the moment it is disconnected. Keep everyone out from under the door. Do not hang on or pull the red cord to lift a door.
Test your opener's auto-reverse every month. With the door open, lay a 2x4 flat on the floor where the door closes (about 1.5 in. high). Close the door. It should reverse when it touches the board. Also wave something through the sensor beam while it closes; it should reverse. If either test fails, stop using the opener and call a professional. Federal rules require residential openers manufactured on or after January 1, 1993 to reverse on contact; follow your opener manufacturer's instructions for testing.
In Arizona, garage door installation and repair for pay generally requires a contractor license from the Arizona Registrar of Contractors. You can check any company's license at roc.az.gov. Same Day Garage Door Services is licensed: ROC 308754 (primary) and ROC 349928.
Never attempt these at home
- Replacing, winding or adjusting a torsion spring.
- Replacing an extension spring or its safety cable.
- Replacing or adjusting lift cables while the springs are under tension.
- Any work on the cable drums or the torsion shaft.
- Replacing a door section while the springs are wound.
Call us instead. A single torsion spring starts at $286.20 + $160 labor ($446.20 in all) on our price list, and we tell you the price before any work starts.
Call (480) 750-7975Which way is right for your job
Do it yourself if
- The job has no stored energy: lubricating the door, testing the auto-reverse, cleaning the safety sensors or resetting a keypad.
- The job is real work that cannot hurt you if you stop: the bottom weather seal, rollers on the bottom sections, sensor alignment or the opener's travel limits.
- You have the time. Most of these take between 5 minutes and an hour.
Hire a pro if
- The job touches a spring, a lift cable, a cable drum or the torsion shaft.
- The door will not stay up, or it drops when you let go of it.
- You want the spring matched to your door. We measure the wire size, inside diameter and length, and the cycle rating is on your invoice.
- You want the work warranted. Our craftsmanship warranty covers the labor on the work we did for one year, and it covers only what we worked on.
A broken torsion spring, by you or by us
This is the job people ask about most. Doing it yourself costs less in parts, and you can check that with one search. The other rows are why we still say do not attempt it.
Dimension
You do it
We do it
01
Price for the job
You do it
The kit and the tools. There is no labor charge.
We do it
A single torsion spring starts at $286.20 + $160 labor ($446.20 in all) on our price list. A double starts at $572.40 + $160 labor ($732.40 in all).
Our figures: our price list.
02
Parts
You do it
$44 to $57 for a complete kit direct, $48 to $117 at the big-box retailers. Doing it yourself is clearly cheaper here.
We do it
Included in the job price. The spring is rated to your door, not chosen from what was on the shelf.
03
Tools you would have to buy
You do it
Winding bars, vice grips and a socket set. The bars must be solid steel and 18 inches or longer.
We do it
Nothing. The tools are on the truck, and the technician has wound several thousand springs.
04
Time
You do it
2 to 4 hours the first time. Longer if a cone is seized or the shaft has scored.
We do it
Usually under 90 minutes. Same day service on qualifying jobs.
05
If it goes wrong
You do it
In every documented injury from this job, the cause is a wound spring releasing. The injuries are to hands and eyes, in that order.
We do it
That is our responsibility, and our insurance.
06
If the wrong spring goes on
You do it
A spring with the wrong rating fails again within a year, even when fitted correctly. On a heavy door it can take the opener with it.
We do it
We measure the wire size, inside diameter and length. The cycle rating is on your invoice.
- We checked retail parts and tool prices on 17 September 2026, and they change. Our figures come from our published price list.
Jobs you can do yourself
These come from our repair guides, where every job is rated by difficulty. None of them involves stored spring energy.
Do it yourself
These jobs involve no stored energy and no special tools. If you can change a smoke alarm battery, you can do these.
Lubricate a garage door properly
15 minutes · $12 of spray
Test the auto-reverse safety feature
5 minutes · free
Clean and check the safety sensors
10 minutes · free
Reset a keypad you have lost the code to
10 minutes · free
Doable with care
These take real work, and it is possible to get them wrong. None of them can hurt you if you stop.
Replace the bottom weather seal
1 hour · $30 to $60
Replace worn rollers, bottom sections only
1 hour · $25 to $70
Realign safety sensors that keep reversing the door
30 minutes · free
Adjust the travel limits on an opener
30 minutes · free
What the evidence says
We do not quote the national injury figure many sites use, because we could not trace it to a primary source. These we could.
The door industry's trade association
DASMA, the association of door and access system manufacturers, says spring systems are dangerous and should be repaired only by trained professionals. It says the lift cables should be replaced only by a trained technician, because of the high spring tension.
DASMA safety tips, read 8 Oct 2026: garage door safety tips.
The manual that came with your opener
Federal regulation requires the instructions for every residential garage door opener to tell you to have a qualified service person repair cables, spring assemblies and other hardware. The rule sets what the manual must say. It does not stop a homeowner doing the work.
16 CFR 1211.16, read 8 Oct 2026: eCFR.
Seven eye injuries, all from home repairs
A 2023 case series from Massachusetts Eye and Ear describes seven patients hurt when a spring came loose at high speed while they were repairing their own garage door. Their final vision ranged from 20/125 to no light perception. Two did not recover any vision, and one eye was removed.
Ophthalmic Surgery, Lasers and Imaging Retina, 2023, read 8 Oct 2026: PubMed record, full text.
A manufacturer's own instructions
Clopay's torsion spring instructions call for two solid steel winding bars, 1/2 inch in diameter and 18 inches long, and say never to use substitutes.
Clopay, read 8 Oct 2026: torsion spring instructions (PDF).
When to stop and call us
Three things people tell themselves halfway through a spring job, and the mechanical reason each one is wrong.
“The spring is only a bit unwound.”
A spring holds the same energy at a quarter turn as it does at seven. There is no partially safe position.
“I can hold the door up while I work.”
With the spring broken, a double door puts 150 to 200 pounds in your hands. That is too much weight to catch.
“I have the part, it is just fitting it.”
Most problems come from torque and balance, not the part. A spring with the wrong rating fails again within a year, even when it is fitted correctly.
Where doing it yourself is the better choice
For most jobs on a garage door, doing it yourself is the better choice. Lubricating the door, testing the auto-reverse, cleaning the sensors and resetting a keypad take minutes and cost little or nothing. A service call from us is $69, and it is waived when you go ahead with a repair (parts and labor).
Some jobs take more care and are still yours to do: the bottom weather seal, rollers on the bottom sections, sensor alignment and the opener's travel limits. None of them can hurt you if you stop.
On a torsion spring, the parts are much cheaper if you do it yourself. A complete kit was $44 to $57 direct when we checked on 17 September 2026. Our price for a single torsion spring starts at $286.20 + $160 labor ($446.20 in all).
Check any of this yourself
Every outside fact on this page comes from one of these. Each takes a minute or two to check.
- DASMA safety tipsThe trade association's guidance on springs, cables and openers.Read DASMA's safety tips
- 16 CFR 1211.16The federal rule that sets the safety instructions printed in every residential opener manual.Read the regulation
- Open globe injuries from garage door springsThe 2023 case series of seven patients. The full text is free on PubMed Central.Read the full text
- Our price listEvery Same Day price on this page, with what moves each one.See the price list
Common questions about doing it yourself
We do not recommend it, and we do not publish the steps. DASMA, the door industry's trade association, says spring systems should be repaired only by trained professionals. Federal regulation requires the manual that came with your opener to tell you to have a qualified service person repair cables and spring assemblies.
Jobs with no stored energy: lubricating the door, testing the auto-reverse, cleaning the safety sensors and resetting a keypad. With care, you can also replace the bottom weather seal and the bottom rollers, realign the sensors and adjust the opener's travel limits.
No. Both store energy. DASMA says a door with extension springs needs a safety cable through each spring, secured at both ends, and that spring systems should be repaired only by trained professionals.
A single torsion spring starts at $286.20 + $160 labor ($446.20 in all) on our price list, and a double starts at $572.40 + $160 labor ($732.40 in all). A pair of extension springs starts at $338.14. We tell you the price before any work starts.
Because most jobs on a door are simple, and paying for a visit to clean a sensor makes little sense. We would rather you call us for the jobs that need us.
Rather we did it?
Tell us what the door is doing. We will tell you what it needs and what it costs before anyone touches it.
Safety and disclaimer. The repair guides and DIY information on this website are provided by Same Day Garage Door Services for general informational purposes only. They are not a substitute for an in-person inspection by a trained, licensed technician, and they may not fit your door, opener or situation.
Garage doors are the largest moving object in most homes. Springs (torsion and extension), lift cables, drums and bottom brackets operate under extreme tension and can cause serious injury, death or property damage if handled incorrectly. We strongly recommend that only a trained professional repair, adjust or replace these parts. Before any work on or near an opener, disconnect power (unplug it or switch off its breaker) and secure all remotes and keypads. Use the emergency release only as described in your opener's manual, preferably with the door closed, and never when a spring or cable may be broken. Keep children and pets clear, and never let children play with remotes or wall buttons.
Test your opener's automatic reversing system and safety sensors monthly, following your manufacturer's instructions. Residential garage door openers are subject to federal entrapment-protection requirements (16 CFR Part 1211, which incorporates UL 325). If your door does not reverse when it contacts an object or when the sensor beam is blocked, stop using the opener until it is repaired.
If you choose to do any work yourself, you do so at your own risk. Same Day Garage Door Services makes no warranty, express or implied, about the accuracy, completeness or fitness of this information for any purpose, and is not responsible for any injury, loss or damage resulting from its use, to the fullest extent allowed by law. Following a guide may void your manufacturer's warranty. Nothing here creates a service agreement or warranty; our warranties apply only to work we perform, under the terms in your written invoice.
In Arizona, paid garage door installation and repair work generally requires a license from the Arizona Registrar of Contractors (verify any contractor at roc.az.gov). Same Day Garage Door Services, ROC 308754 (primary) and ROC 349928. Questions? Call (480) 750-7975 or visit our scheduling page.

